Tag Archives: troubleshooting

GSWA 6: Talking to the Cloud

Okay, chapter 6 of Getting Started with Arduino, “Talking to the Cloud,” has been the bane of my arts technology existence. I did most of this chapter about three weeks ago and couldn’t get it to work. The problem is that the book as a whole seems to progress like this:

  • Chapter 1: No real information
  • Chapter 2: A tiny bit of information but no practical work
  • Chapter 3: A tiny bit more information but still no practical work
  • Chapter 4: A tiny bit of practical work
  • Chapter 5: A little bit more practical work
  • Chapter 6 (this chapter): About 1000% more complicated than all the rest of the book put together
  • Chapter 7: A tiny bit of information to wrap things up

It really felt like getting thrown into the deep end. However, I finally got it to work. Here is the chronicle of my adventure:

  • Copy and paste code into Arduino and Processing IDEs (because this one uses both).
  • Get intractable errors in Processing because the code was written for v. 1 and we’re now in v. 2
  • Spend much time searching the web, determine that all of the Java libraries must be installed manually
  • Get the Processing code running (see first photo above) but get such miserably low numbers for output that no light would be detectable
  • Revise Processing code to search for more common terms with the hope to being able to see things (see second photo)
  • With Processing apparently working right, turn to physical components of Arduino
  • Reconstruct the physical circuit because I took it apart after three weeks (having even schlepped it around with me in a box on the bus and train from Salt Lake City to Orem)
  • Plug the Arduino board in to my computer
  • Have the Arduino shut off and get alarming error message from computer (see third photo)
  • Spend much time fiddling with USB connection, pull out brand new, back-up Arduino board, plug it in and see that it works, recreate circuit on new board, get same problems, notice lots of heat on bottom of first board, think that I have destroyed things, fret much
  • Search web for help and learn that there may be a short-circuit (without even really knowing what this would mean)
  • Eventually discover that I put the ground wire on the same positive rail of the breadboard as the power. Oops.
  • Put the ground wire on the negative rail (the way the illustration told me to do it in the first place), board powers up, problem solved.
  • Back to Arduino IDE, compile and upload sketch, have lights blink to indicate successful upload, but see nothing happening with LEDs
  • Mess around with light sensor and the button on the breadboard to no effect
  • Check the serial monitor in Arduino and see a steady stream of strange data that is absolutely not in the right format
  • Read book again, see “important message” about serial port selection
  • Go back to Processing, uncomment code that lists serial port connects and find that my Arduino is connected to port 5 and not the expected port 0
  • Change port in Processing, rerun sketch, and suddenly see much blinking on Arduino board
  • LEDs light up! Button turns them on and off! Success! (See last, triumphant photo above)

Okay, that was not fun but I was convinced that I would never make it work so I feel very, very happy now. And I already finished chapter 7 (although I haven’t yet posted it to this web page because I’m an extremely linear guy), so I’ll post this chapter, post that one, and then try to do a small, creative project (which I have been planning – more or less – for a few weeks), and call it quits. But here we go for now!

Completed:

  • Getting Started with Arduino, 2e, Ch. 6: Talking to the Cloud (1 exercise – but a really, really big one)
  • Sketches (i.e., code) can be downloaded from http://db.tt/f6x9Q4NA
Tagged , , , , , ,

GSWA 7: Troubleshooting

First Computer Bug

The last chapter of Getting Started with Arduino is about troubleshooting. In its honor, I have posted a picture of the first known computer “bug” above. (Or, at least, the first literal computer bug. See the photo source here and a Wired commentary here.) The chapter is very short and starts by suggestions the following principles:

  • Understanding. That is, it is very helpful if you understand how all the parts in your project function and how they contribute to the intended final product.
  • Simplification and segmentation. Break the project down into smaller pieces and try to check/fix each part separately.
  • Exclusion and certainty. Test each part separately and be certain that it works.

The chapter then recommends starting by looking at the Arduino board, then the breadboard, then the Arduino IDE. Also, there are some useful resources available at the Arduino website, but good old Google works well, too.

And, by the way, was able to use essentially all of the principles in trying to sort out several problems with the sketch that I did for chapter 6, so I’m glad for the advice.

Completed:

  • Getting Started with Arduino, 2e, Ch. 7: Troubleshooting (0 exercises)
  • Sketches (i.e., code) can be downloaded from http://db.tt/f6x9Q4NA

 

Tagged , , ,